GPS L1 ANTENNA
Lightning Protection Device for RET
Lightning Protection Device for RET The Lightning Protection Device (LPD) is designed for lightning protection of control cables carrying partial lightning currents up to 25 kA (shield) and 2.5 kA (inner conductor), according to IEC 61643-1, IEC 61312-3. Each pin is protected individually. For outdoor and indoor use.
50A Circuit Breaker, E/M Trip, Bullet Nosed
DS1 Interconnect Panel 28 Circuits RJ48c 19 inches
The D1M-1E1016 is a 28-circuit bantam interconnect panel. Bantam interconnect panels contain pairs of jacks that are internally connected together. These panels utilize the same bantam jacks as the DSX-1 panels, but the permanent internal connection between jacks dedicates two network elements to each other.
The DB224 is a heavy duty, light weight, high gain antenna.
The DB224 is a heavy duty, light weight, high gain antenna. It is suitable for mounting to the top or on the side of a tower. Clamps for top mounting are supplied with the antenna; an additional side mount kit (DB5001) must be ordered for side mounting.
ELECTRICAL DESIGNThe antenna is a four stack collinear array designed to pro- vide high gain, broad bandwidth and minimum pattern dis- tortion. A binary cable harness is used to ensure equal in- phase power distribution to all radiating elements.
OPTIONAL RADIATION PATTERNThe DB224 can be used as an omnidirectional antenna hav- ing a gain of 6 dBd or as an elliptical pattern antenna having a maximum gain of 9 dBd. An omni pattern is achieved when the four dipole elements are spaced evenly, every 90° around the mast (Figures 1 and 2). An elliptical pattern is obtained when all four dipole elements are positioned in a line (col- linear) along the mast. When top mounted, the omni and elliptical models provide radiation patterns as shown in Fig- ure 3. When side mounted, the two models provide signifi- cantly different radiation patterns (see SIDE MOUNTING and Figure 4). The antenna can be changed in the field from one pattern to the other using ordinary hand tools.
We have the installation instructions available for this product upon request.
18 dBi, 5.25 - 5.85 GHz
ANTENNA, ARGUS 65deg HPBW QUAD 24" w/RET in/out
RAN Antenna, ARGUS 65deg QUAD POLE W/iRET 48"
Patented coil inductor, dc block, lightning protection, engineered for high power of combined signals operating from 1.8 GHz to 3.8 GHz and 4.2 GHz to 6.0 GHz band pass configured with N male equipment side and N female surge connectors
Patented PolyPhaser protection for single or multi-channel transmitters and / or receivers. Industry's BEST RF performance, fully weatherized, compact integrated connector housing, Industry's lowest throughput energy, maintenance free, and multi-strike compatible.
0.6 m | 2 ft Standard Parabolic Unshielded, Dual-Polarized Antenna, unpressurized, 5.250–5.850 GHz, N Female, gray antenna, molded gray radome with flash, standard pack—one-piece reflector
TPR10 VALERE RING TERMINAL TEMP PROBE 10"
VALERE RING TERMINAL TEMP PROBE 10"
PTP 600 Series Ethernet Bridge with Wayside T1/E1. 5.4 GHz WRC Band System, 300 Mbps Backhaul Module Pair - Connectorized, Complete Link.
The PTP 54600 connectorized end operates in the 5.470-5.725 GHz license-exempt radio frequency. Channel size is configurable to 5, 10, 15 and 30 MHz; with aggregate throughput up to 300 Mbps at the Ethernet layer. The PTP 54600 uses 25dBm transmit power with up to 166 dB system gain using an integrated 22 dBi antenna. Receiver sensitivity falls between -98 and -58 dBm. The Cambium PTP600 Series combines the speed and reliability of licensed wireless with the flexibility of the unlicensed space. These high performance Ethernet Bridges offer more range, more capacity, and more ways to use the unlicensed spectrum. The PTP600 Series delivers an aggregate Ethernet data rate of up to 300Mbps making these radios 300% more spectrum-efficient than competitive products. When interference is encountered, it automatically applies frequency selection and adaptive modulation to mitigate the effects. The PTP600 series is optimal in any application where high throughput and/or T1/E1 capability are major requirements such as business enterprises, government agencies and service providers. The PTP600 links can deliver 99.999% availability in virtually any environment, including non-line-of-sight, long-distance line-of-sight, high interference, water and desert. An ideal solution for building to building and campus connectivity: as well as, disaster recovery, distance learning and telemedicine.